ESAB · TIG Welding (GTAW)
The ESAB Fabricator ET 410iP is a heavy-duty inverter-controlled power source for HF TIG pulse and MMA welding, rated 410 A at 60% duty cycle and 310 A at 100% at 40 °C, with pulse frequency from 0.5 to 250 Hz, Start Pulse tungsten preheat, spot mode and a wide 380–440 V mains tolerance.
Price on request. POFIS is an ESAB Authorized Distributor & Service Centre in Abu Dhabi — quotations include confirmed lead time and delivery terms.
Where it is used
Features
A micropulse at ignition preheats the tungsten electrode, which ESAB state improves arc stability from the start. A cold tungsten gives an unstable first few seconds, and on a short weld that is most of the weld — so this matters more on tacking and small components than on long runs.
Pulse background current is adjustable between 10% and 90% of the set current, with frequency from 0.5 to 250 Hz. That range covers slow pulse for puddle control on open roots through to high frequency for arc constriction on thin material.
Spot mode gives repeatable tack welds at a set duration. 4TS allows pulsing to be switched in only when needed within a weld, rather than committing to it for the whole run.
Accepts 380, 400, 415 or 440 VAC at ±15% three-phase. The combined range runs from roughly 323 V to 506 V, which covers most regional supplies and gives stable welding where the supply is not.
HF start establishes the arc without the tungsten touching the work, preventing tungsten inclusions in the weld — which on pressure vessel and pipeline work is a rejectable defect.
Idle power is 40 W with VRD off and just 15 W with VRD on. Maximum open circuit voltage is 76 VDC, dropping to 13.5 VDC with VRD active for work in environments with increased electrical hazard.
Rated IP23S at 35.2 kg in a 525 × 280 × 475 mm case, with an intuitive control panel ESAB state reduces the time taken to reach the right weld characteristics.
Technical data
Published manufacturer specifications. Where a figure affects your welding procedure, confirm it against the instruction manual for your specific configuration.
| Mains voltage (welding input) | 380 / 400 / 415 / 440 VAC ±15%, 3 ph, 50/60 Hz |
|---|---|
| Fuse, slow | 32 A |
| Efficiency at max current | 88% MMA, 86% TIG |
| Idle power consumption | 40 W (VRD off); 15 W (VRD on) |
| Maximum open circuit voltage | 76 VDC (13.5 VDC with VRD on) |
| Welding output at 40 °C | 410 A at 60% duty cycle; 310 A at 100% duty cycle |
|---|---|
| Setting range, MMA / TIG | 30–410 A / 5–410 A |
| Pulse background current range | 10% to 90% of set current |
| Pulse frequency | 0.5–250 Hz |
| Dimensions (L × W × H) | 525 × 280 × 475 mm |
|---|---|
| Weight | 35.2 kg |
| Enclosure class | IP23S |
| Operating temperature | −10 °C to +40 °C (+14 °F to +104 °F) |
Ordering information
Quote these part numbers on your enquiry or LPO to guarantee the exact configuration. If you are unsure which variant suits your application, send us the joint details and we will specify it.
| Description | Part number |
|---|---|
| Fabricator ET 410iP, CE | 0447101881 |
| Fabricator ET 410iP, non-CE | 0447101880 |
| Description | Part number |
|---|---|
| SR-B 26 HD torch, air-cooled, OKC 50, 4 m | 0700025526 |
| SR-B 26 HD torch, air-cooled, OKC 50, 8 m | 0700025527 |
| SR-B 18 torch, water-cooled, OKC 50, 4 m | 0700025550 |
| SR-B 18 torch, water-cooled, OKC 50, 8 m | 0700025551 |
| COOL 2 water cooler | 0465427880 |
| Water cooler adapter for COOL 2 cooler Required to fit the COOL 2 to this machine. | 0447248001 |
| Coolant, 10 l | 0465720002 |
| Description | Part number |
|---|---|
| Trolley 3-in-1 for water-cooled system with COOL 2 and adapter | 0349313450 |
| MMA 4 analogue remote control, incl. 10 m cable and 8-pin connector | 0700500084 |
| TIG foot control, 4.6 m cable and 8-pin connector | W4014450 |
Downloads
Need the instruction manual or spare parts list for this machine? Request it from weldiv@pofis.ae and we will send the current revision.
Frequently asked
410 A at 60% duty cycle and 310 A at 100%, both rated at 40 °C. The setting range is 5–410 A in TIG and 30–410 A in MMA.
A micropulse at ignition that preheats the tungsten electrode, improving arc stability from the start. A cold tungsten gives an unstable first few seconds — which on tacking and short welds is most of the weld.
Frequency from 0.5 to 250 Hz, with background current adjustable between 10% and 90% of the set current. That covers slow pulse for open-root puddle control through to high-frequency pulse for arc constriction on thin material.
A trigger mode that lets pulsing be switched in only where it is needed within a weld, rather than running pulsed for the whole pass. Useful when part of a joint needs heat control and part does not.
380, 400, 415 or 440 VAC at ±15%, three phase, 50/60 Hz. The combined tolerance spans roughly 323 V to 506 V, which gives stable welding on supplies that vary.
Only for water-cooled torches such as the SR-B 18. Note that fitting the COOL 2 cooler (0465427880) to this machine also requires the adapter 0447248001 — order both or the cooler will not connect.
The 410iP gives more output (410 A against 350 A at 60% duty cycle) and a wider mains tolerance, but weighs 35.2 kg against 16.3 kg. The 350iPA is the portable one with engineered cellulosic and basic electrode curves; the 410iP is the heavy shop machine.
POFIS is an ESAB Authorized Distributor and Service Centre in Abu Dhabi. Request a quotation on this page or email weldiv@pofis.ae for price, CE variant confirmation and lead time.
Procurement & supply
The ESAB Fabricator ET 410iP is supplied from Abu Dhabi by Perfect Oilfield & Industrial Supply LLC as an ESAB Authorized Distributor and Service Centre. The information below covers what procurement and QA/QC departments normally need before raising a purchase order.
Stock items dispatch from Abu Dhabi within 24–48 hours. Indent items are quoted with a confirmed lead time at the time of offer.
POFIS is an approved ADNOC vendor and is listed on the approved vendor lists (AVL) of major operators and EPC contractors across the GCC. We can complete supplier registration and prequalification documentation on request.
Standard credit terms are available to registered corporate accounts. LPO, LC and advance payment are all accepted.
Delivery across the UAE and the wider GCC. Quotations can be issued on EXW, FOB, CIF or DDP terms to suit your project.
Full manufacturer warranty, honoured locally. As an ESAB Authorized Service Centre we carry out warranty work and repairs in Abu Dhabi rather than returning equipment abroad.
In-UAE service, commissioning, operator training and spare parts backing for every machine we supply.
Price on request
Send the form and the POFIS welding division replies with pricing, confirmed lead time, delivery terms and availability. Tell us who you are and what the job is, so the reply can be specific to it rather than a catalogue price list.
